Deer Hunting Forums banner

1 - 10 of 10 Posts

·
Registered
Joined
·
195 Posts
Discussion Starter #1
I have ordered a new fully rifled slug barrel from bass pro for my mossberg 500 with cantilever scope mount.i want to try the sst slugs.please give me some advice.i've never slug hunted,and can't wait for the chance.also.i'm thinking of either a bushnell 3200 3x9 or a simmons aetec for the scope.
 
G

·
i don't know a thing about slug guns. i have 2 old simmons atecs and love them. thats why i got a third for my 338 win mag last year. the new one was junk. didn't feel the same. didn't seem to be as well built. turns out it wasn't. 3 shots and it crumbled.
 

·
Registered
Joined
·
195 Posts
Discussion Starter #4
I hate to hear that the new aetecs are junk.i'm waiting on one to be delivered.as far as sabots in a slug gun,i believe the sst's are in a sabot.i've taken deer with bow,rifle,muzzle loader,and pistol,but not with a shotgun.i can't wait to try.i'm just looking for info about slug hunting.the new slugs are pricey.i'm just trying to decide which ones to try.
 

·
Registered
Joined
·
517 Posts
I have used the sst's for a few years and loved them but again they are expencive to shoot.i have tried just about every slug out there in my reminton 1100 and these slugs worked best for me.i had got just under 2in grpups at 100yrds.which isn't to bad for a shotgun!these slugs are the fastest and most accurate in my slug gun.but every slug gun shoots different.i hear the lightfield slugs shoot very well to you might want to check those out.
 

·
Registered
Joined
·
195 Posts
Discussion Starter #7
Well, i'm off to academy in joplin to buy some sst's.i may buy another brand also to try.i'm afraid it's going to be costly just to get the gun sighted in.
 

·
Registered
Joined
·
517 Posts
well, i'm off to academy in joplin to buy some sst's.i may buy another brand also to try.i'm afraid it's going to be costly just to get the gun sighted in.
you could allways get just a cheap box of sabot slugs just to get you on the paper?i don't know how true this is but i heard if you site your gun in at 25yrds it will be dead on at 100yrds?does anybody know if this is true?
 

·
Registered
Joined
·
53 Posts
i don't know how true this is but i heard if you site your gun in at 25yrds it will be dead on at 100yrds?does anybody know if this is true?
You should fire a slug gun at 50 yards to set your windage as a slug is very susceptible to wind drift (just a 10 MPH wind can push the slug 6" at 100 yards). Here is a way to shorten the amount of ammo to sight in a firearm. Shoot two shots (to make sure you have a good grouping) from a bench using a rest. Now replace the rest with a gun vise (DO NOT SHOOT FROM THE GUN VISE). Lock the shotgun in the vice so the cross hairs of the scope (or iron sights) are perfectly centered on the bullseye. Now adjust the scope or iron sights (without moving the gun or gun vise) so they are centered in the point of impact on the target. Replace the gun vise with the gun rest and test fire one or two rounds. If it is close, you can then put the shotgun back in the vice to set the elevation. If you know how high you want the shot to be at 50 yards you can now set the elevation. Now, replace the gun vise with the gun rest and try your long distance shot (100 or 125 yards, etc.) Make any fine tune adjustments on the elevation and then shoot at 50 yards to recheck your windage.
 

·
Registered
Joined
·
195 Posts
Discussion Starter #10
Well everywhere i went in joplin,did not have the sst's.so i will order them.and that's a good idea,i will use some cheaper slugs to get on paper.if not,i'm afraid it will cost 50.00 or more to get dialed in.but,i do shoot from a rest,and i'm ordering a remote trigger release to take some of the pain and human error out of it.
 
1 - 10 of 10 Posts
Top